Your drone’s battery is an essential component that requires very specific care. If you do take care of it, you will inevitably prolong its life and optimize your flight duration. Alternatively, if you don’t take care of them, you’ll shorten their life.
Charging your drone battery
- When you first receive you new drone battery, if you plan to use it right away, charge it up to 100%. If not, it’s optimal short-term storage level is 70% (intelligent charging units, such as the senseFly SmartCharger, enable this kind of charging precision).
- 1-2 days before your battery’s first operation, charge it up to 100%. Then, when your flights are over, charge your battery again to 70% until its next use.
- If you notice a significant drop in your drone’s available flight time after fully charging one of your batteries, do not continue to use or charge that battery. Such a reduced power capacity can indicate an internal fault.
- Immediately after flight, your UAV’s battery may be hot. To avoid potential damage, wait until the battery is cool enough to hold in your hand before charging it again.
- If possible, always charge batteries in a LiPo guard bag (see image below) as these are designed to limit the spread of fire or explosion.
- Never charge a swollen battery, one that is leaking or one that has been damaged.
- If you notice a suspicious smell, noise, or smoke emanating from your battery or charger, disconnect it immediately.
- Only charge your UAV’s battery with a manufacturer-approved charger. Do not attempt to charge your drone battery with any other unit.
- Never use a damaged charger.
- Since there is always some degree of risk that a battery will catch fire, do not charge batteries near ﬂammable materials, or on ﬂammable or conductive surfaces such as carpets, car seats, wooden ﬂooring or wooden furniture. Try to charge batteries on nonflammable and nonconductive surfaces, such as in a large ceramic bowl.
- While charging, do not leave the battery unattended, do not cover it or store it near a source of heat.
- Do not attempt to charge a battery if the ambient temperature is below 0° C (32° F) or above 40° C (104° F), or if it is still installed inside your drone.
- Pro tip: for efficient battery management, label each battery with a number (think: magic marker or stickers). That way, you can note down each battery’s charging status. Plus, you’ll know at a glance which battery was used for each flight, which is useful when logging your operations.
Storing your drone battery
- Do not keep a LiPo battery either fully charged or discharged for more than a month. If you need to store a battery for a while and its level of charge is too high, use up some power with a short flight. If too low, charge it back up to 70%.
- Do not leave a battery in your drone for extended periods of time. When possible, store batteries in the drone’s case instead.
- If you need to store your batteries elsewhere, avoid direct sunlight and store them in a cool indoor location.
Safe handling of your drone battery
- Avoid all contact with battery electrolyte—an electrically conductive liquid solution inside the battery—as well as electrolysis vapours. In the event of a battery leak, do not allow your battery’s contents to come into contact with your skin or eyes.
- In case of contact with the skin, wash copiously with soap and water.
- In case of contact with the eyes, rinse copiously with cold water, then consult a doctor.
- In case of inhalation of electrolysis vapours, seek medical help immediately.
- Inspect your batteries and charger regularly for damage to the cable, plug, enclosure or other parts. Do not use the battery if the plastic cover has been torn or compromised in any way.
- Do not expose the battery to excessive physical shock such as impact (try not to drop it!) or crushing force. Equally, do not place any heavy objects on your battery or charger.
- Keep batteries out of reach of children.
- Do not allow your drone battery to come into contact with any kind of liquid. E.g. do not leave your battery/drone out in the rain or near a source of moisture.
- Do not put your battery in a microwave oven or a pressurised container.
- Do not attempt to dismantle, pierce, distort or cut the battery and do not attempt to repair the battery or charger.
- Do not transport batteries in the hold of an aircraft, or any other area of an aircraft that is inaccessible during ﬂight. Transport them in your hand baggage or preferably in a battery-safe bag.
- Plan your drone’s flights so that they are comfortably within the limits of the battery.
- Pro tip: leave a little extra time at the end of each flight in case your drone needs a little extra power for any reason, for example, to counteract strong winds or to hold its position while waiting for the landing zone to clear.
- The lower you push a battery’s charge—hitting regularly below 20%—the shorter that battery’s life, and the lower its reliability, will be.
- In low temperatures, or when there are strong winds, adapt your missions with shorter flight times in mind—when winds are strong, your drone uses more power, while low temperatures cause the chemistry of the battery to change and it to discharge more quickly.
- In cold conditions, where the air temperature is below 5° C (41° F), try to keep your UAV’s batteries warm—ideally at least 5° C—before connecting them to your drone.
Discharging Batteries (before traveling)
Disposing of your drone battery
- Do not discard of batteries with household or commercial waste—this harms the environment.
- Damaged or unusable batteries must be disposed of properly, for example, in a container specially reserved for this purpose, following appropriate local guidelines and regulations (see image above). For more information, contact the distributor from whom you purchased your drone or your local municipal authority.
- Do not dispose of a battery by setting it on fire.
There are different kinds of Lithium based batteries, and this is the battery you’ll want if you need one for a phantom drone. but the most common for Drone use is the Lithium Polymer cell, due to the lightweight construction and the performance associated with this type of battery.
From something as small as a single cell 100mAh battery you’ll find in Nano Proto X quadcopter, all the way up to 6 cell 22000mAh packs we’re now seeing in larger Drones! If you fly a DJI Phantom, a single battery constitutes more than 10% of your unit cost at $129 (versus the most expensive Vision+ that runs at $1159 today). So whether you are getting the most out of those batteries or not makes a lot of difference. Battery failure could cause malfunctions and even a crash, so a bad battery can actually cost you a lot more than just its replacement value.
Over the years we’ve seen continuous improvements in battery technology and I’m sure further improvements are on the horizon!
Quick tip – Travel & Charging Bags for Lipo Batts
If you’re just starting out with LiPO Drone batteries we suggest you make sure to charge them inside a 9 x 12 inch protective LiPO charging bag, or 175 x 60 x 75mm size, also there is the 9 x 7 x 2inch size, whatever best fits your batteries.
Stop worrying about what to get for your kids this holiday season. Dronethusiast provides guides for drone shopping for every type of drone! Get some help by reading up on our drone deals article.
NiCad’s and NiMH’s
For decades we’ve been using nickel-cadmium (NiCd) batteries, later followed by nickel-metal hydride (NiMH). These have always served us well and still do. With these batteries, maintenance has always been key to maximising performance and durability. Neither like to be left for long periods of time without being cycled or topped up and both suffer from high internal self-discharge.
NiCd batteries will typically lose approximately 1% of their charge per day; worse still NiMH batteries can lose as much 5-20% of their charge on the first day and 1-4% per day after that. Newer LSD (Low-Self-Discharge) NiMH battery technology such as Eneloop from Sanyo and others reduces this problem, but they still suffer.
Lithium Polymer batteries don’t self-discharge anywhere near as much.
Typically, you can leave a fully charged LiPo on the shelf for a month and it might only lose 1% of its capacity. It means, in theory, you can leave a fully charged pack on the shelf for a month or two and just pick it up and go flying.
So, everything you know about NiCd & NiMH batteries must now be put to one side. LiPo cells demand a different level of respect and different rules apply. I’m sure some of you know the potential dangers of Lithium cells if used incorrectly, yet if used correctly, you shouldn’t have a problem and they’ll serve you well.
In this guide, I will talk about how to treat your batteries and make sure you get the most out of your investment. It can be the difference between getting less than 50, or more than 200 cycles!
So, imagine you’ve just purchased a new setup. Along with your new equipment, you’ve also purchased a number of shiny new battery packs and discovered they cost a considerable amount of money, especially modern DJI batteries!
New Drone Battery Care
If you’ve ever purchased a new battery and checked the voltage, you’ll discover that each cell will be at approximately 3.8/3.85V per cell. This equates to approximately 40% of capacity and over the years, manufacturers have to come to the conclusion that this is the best condition for cell storage over long periods. All new batteries arrive in this condition.
I’m sure most of you will have bought a new mobile phone only to discover that the battery is partially charged. You now understand why! When charging new batteries, it is advisable not to fast charge for at least the first few cycles.
This means charging no faster than ‘1C’ (I’ll explain charging rates in more detail later). The same applies to the first few discharge cycles. Some say that this isn’t essential. However, it certainly won’t do any harm. It’s thought that a ‘Breaking In’ procedure is a good idea.
The idea is to fly gently and only discharge you batteries to 50% for the first few flights. This is thought to help settle the internal makeup within the battery and help set the pack up for a prolonged life. After the first few cycles, it’s not unusual to see a slight increase in performance and usually a sign that the pack is ready for normal use.
Charging Lithium Polymer Batteries
It is extremely important you only use a charger specifically designed for charging Lithium Polymer cells. All new chargers now come with a balancing feature which is essential for both safety and battery life reasons.
The stated operating voltage of a typical Lithium Polymer cell is from 3V to 4.2V when fully charged. Discharging cells below 3 volts will invariably cause irreversible damage and charging above 4.2V is dangerous and easier to achieve than you might think! If you have a selected the ‘LiPo’ function, your charger will be set to peak detect cells reaching 4.2V at which point the charger will cut off. Set the wrong type of battery; begin charging beyond 4.2V, the pack will swell and if left, will eventually catch fire! Yes, it’s that dangerous, so please be vigilant when setting your charger!
Some modern battery packs such as the one that powers the DJI Phantom 2 quadcopters come in a form factor that slips safely into the camera drone itself so you don’t have to connect them manually. For these kinds of batteries, there are charging stations available because it is possible to create a compartment or housing that let’s you simply slip batteries into.
You might think that the only benefit of such a charging station is that you can charge batteries in parallel. Well, there is a lot more to it. I have seen people use parallel charging boards and spot on, they only cost like ten bucks. Wicked.
But what they will not necessary tell you is that many of these charging boards (at least the cheap ones) will charge 3 batteries 3 times longer, so you don’t save any time using them for your drones. Ok, maybe having to plug the next battery in takes some time, but no considerable gain I am sure you agree.
If you are looking for a “home” for your batteries where they can rest peacefully and safely while charging, you need solution like this one.
The Spinido Battery Dock Intelligent Charging Hub, designed for safe and fast charge or Phantom 2 and 3 batteries. It’s also suitable with the Inspire 1-100w charger and Inspire 1-180w Rapid Charger. This allows you to intelligently charge up to 3 batteries at the same time, while each battery’s charge is shown with an LED indicator. It’s future proofed by an integrated port for firmware updates when needed and the power is managed to each battery to ensure safe charging. Furthermore it’s made with high quality materials, that are going to last and protect your investment.
Almost all Lithium Polymer batteries you buy today will come with a ‘C’ rating. The ‘C’ in C rating stands for Capacity. The C rating is the maximum, safe, continuous discharge rate of a pack as specified by the manufacturer, so when you see 20C printed on your label, it means it can be discharged at 20 times the pack’s capacity, ‘continuously’.
Capacity is usually measured in mAh and a popular cell size is 2200mAh. Therefore, so by way of example:
2200mAh 20C Cell = 2.2A x 20 = 44A continuous discharge
Along with the continuous discharge rate, some batteries display ‘burst’ discharge rate. This is typically twice the continuous discharge rate. It usually means the battery is capable of allowing twice the current, but only for a few seconds at a time.
You will damage your batteries if you use them beyond these specifications. The idea is to stay well away from these limits. In theory, the higher the C rating, the better the battery. In high current draw applications such as 3D RC helicopters, high C rated batteries are essential. The trouble with 3D helicopters is that the cells are subjected to high current draws in hard maneuvers. The current draw spikes are sometimes beyond the limits of the battery. If the battery is pushed beyond its limits, the battery will get hot, the performance will drop and if pushed hard enough, possibly inflate and cause irreversible damage.
How Good is your Lithium Polymer Battery?
Please, please, please beware of ‘claimed’ C ratings! Most batteries now come from China and at present there seems to be no control on what manufacturers can print on their labels and no requirements to substantiate their claims. I’ve seen countless batteries clearly over specified which cannot deliver anywhere near their claimed current draw! On the flip side, I’ve also used and sold 20C packs which clearly outperform other manufacturers claiming 45C! It can be confusing to determine the genuine specifications as vaunted.
Please do your research, ask around and spend wisely – cheap and good as well as expensive and poor can still be found in the market today! I’ve tested hundreds of packs and to this day, I’ve never seen a pack perform beyond 35C. If you see anyone claim beyond 35C, you should be skeptical!
Balancing Lithium Polymer Batteries
Balancing is very important. If a pack is used and kept within its safe working limits, cells tend not to drift too far out of balance. Imbalanced cells can occur when the pack has been discharged too much. Sometimes a pack may just develop a bad cell. Balance charging will help detect an imbalance between cells and reduce the likelihood of overcharging other cells within the pack. For this reason, please ONLY balance charge your batteries.
When charging your batteries, temperature is important. Never charge a battery that has been stored below 0ºC as you risk an explosion at these temperatures. Cold storage for LiPo cells is actually a good thing, but before charging them again always make sure your packs have had the chance to fully reach room temperature before commencing!
When charging, check the temperature of the battery by hand. If charging at a 1C charge rate, the battery shouldn’t get warm. However, I frequently charge 3C and packs do get slightly warm. Excessive heat means there is something wrong, STOP CHARGING!
After a flight, you may find your batteries are warm to touch. It may be a good idea to give the packs a chance to cool a little before recharging.
Never try charging a pack that has been crash damaged, you run the risk of fire! Cells that are obviously swollen or have physical damage should never be used and careful disposal is required, especially if the cells are swollen.
If you have a pack sitting on the shelf, fully charged, never try topping it up!
NEVER LEAVE A CHARGER UNATTENDED!
The most important point above all, knowing how potentially dangerous a LiPo battery can be if something goes wrong, NEVER leave your batteries on charge unattended! No matter how safe you THINK your charger is, things can and really do go wrong from time to time.
You are at the mercy of technology and some of the worlds most experienced users have had serious accidents with LiPo batteries, including the RC helicopter legend, Curtis Youngblood who seriously burnt his hand through a faulty charging process. So please be careful! Also never charge LiPo batteries inside your house if you can really help it. There are countless videos and images spread all over the internet from LiPo fires, please have a look and beware some of the images are shocking!
The general consensus has always been to charge your LiPos at a rate of 1C, e.g, a 2200mAh battery would be charged at no more than 2.2A. Charging above 1C was once considered bad for battery health. There are still some diehards out there who are adamant that this is still the case. Over the last two years, I’ve been surrounded by packs being charged at 3C and seen absolutely no difference in lifespan! I’ve even carried out tests with packs charged at 1C and 3C, the resulting lifespan was the same.
I prefer 20 to 30 minute charge times myself and feel that almost all modern LiPo packs are more than capable of being charged at 3C without causing any damage. Some manufacturers now quote 5C or even 8C, but through my own tests, packs do sometimes tend to come off the charger a little too warm for my liking and essentially, it’s excessive heat which causes a battery to eventually fail.
Discharge Rates & Level of Discharge
Earlier I explained what a C rating is. We already know that discharging at a rate beyond the specified C rating will damage a battery. Equally damaging is deep discharging a battery. Most damage to lithium polymer batteries is caused by the user running batteries flat and regardless of the quality of the cells, if you run your battery flat, you will cause irreparable damage and wear your battery out very quickly!
Leaving an acceptable level of charge in the battery is by far the most significant factor in prolonging battery life and the most common reason for early battery failure is to ignore this advice! Discharging lithium polymer batteries beyond 80% of their capacity can significantly reduce the lifespan of any LiPo battery. Tests have proven that batteries that are only discharged to 50% can be cycled at least 3 times the lifespan of batteries that are regularly flattened.
A battery that is flattened every time it’s used, may only last 40-50 cycles, so aim for no more than 80% or certainly a resting voltage of 3.6V or more per cell and you’ll get a lot more from your cells. Sticking to this rule I’ve seen more than 150 cycles from many of my own packs. Yet still, the mythology that abounds leads so many fliers to concentrate on charging rates which have never been the issue, rather than excessive discharge levels. I’ve seen people religiously charge at less than 1C and then go fly a battery completely flat, which is a double blunder! So please make sure you time your flights to leave more than 20% left in your packs and enjoy more cycles!
Lithium polymer batteries operate best when they are warm. They are capable of operating right up to 60ºC, and conversely, don’t work very well in cold temperatures. A warm battery is a happy battery but go beyond 60ºC and damage starts, with evidence in the form of puffing or inflation like a balloon if taken to extremes. Cold weather is definite problem.
If you ever indulge in winter flying, note how your batteries just don’t perform the way they do in summer weather! On a freezing cold day, the voltage drop off can be enough for ESCs (Electronic Speed Controller) to hit voltage cut off under load.
Lithium polymer batteries like a bit heat in them before they start performing. When researching, I came across varying ideas regarding optimum working temperatures, but it is safe to suggest that somewhere between 30-40C is optimum. So if you’re out flying on a cold winter’s day, make sure your packs are warm before you start flying.
I’m going to draw from my personal real world experiences here. Manufacturers state that when storing lithium polymer batteries for any length of time, we should store them ideally at a temperature of between 5ºC & 27ºC. The lower the temperature the better.
The optimum voltage for long-term storage, as already mentioned is 3.8-3.85V per cell. Best practice after a days flying, is to charge them back to storage voltage using the storage function on your charger. However, if you do happen to return home with a fully charged pack and intend to go flying the following week, I personally leave my packs charged ready for the following weekend.
My argument here is returning a fully charged pack back to storage is effectively using one of your precious cycles and is likely to do more harm than just keeping it fully charged for your flying session the following week! Heat is more of an issue here. If you do have a fully charged pack, keep it at room temperature or below. Over the years, real world testing has shown that packs which are left fully charged for long periods of time and are subjected to heat, deteriorate and loose capacity.
So always aim to use all of your charged packs when out flying and charge them back to storage afterwards. Always store them in a cool, dry place. Purchasing of LiPo safe bag or ammo box to store packs in is certainly good idea, too.
A good example for a small and inexpensive LiPo bag:
‘Puffing’ – Why does this occur?
There are many reasons why this takes place, with a combination of events and actions invoking cell swelling. From poor manufacturing standards using poor materials to incorrect usage, or just wear and tear with age, but the overall result is the same, the battery is tired and past its best if swelling has started to show!
A few years back there were noted problems with some of the cheaper cells from China. It was discovered that the primary reason for premature cell failure was water contamination in the manufacturing plants. Many factories are in humid climates and high humidity causes water to be trapped inside the cells, which causes Lithium oxidation.
The oxygen can then be freed by electrolysis and with nowhere for the oxygen to escape, the battery then begins to puff. Poor separator construction used in cheap cells is also a factor with bad separator formulation being a contributing factor. Manufacturing processes have come a long way since and poor materials and poor manufacturing are much less of an issue today!
Puffing can also occur if cells are overcharged or charged too quickly. When this happens, you end up with excess free lithium on the anode (metallic lithium plating), and free oxygen on the cathode. A free oxygen atom is small enough to freely move over the separator without carrying an electric charge, resulting in lithium oxide or lithium rust. You then have the problem where lithium oxide uses fewer oxygen atoms than existed in its ionized state and the result is more free oxygen. To emphasise this point, if you were to overcharge a LiPo battery underwater, it would still catch fire as it produces its own oxygen supply!
Over discharge lithium polymer batteries or discharge them too quickly, and the reverse to the above takes place. You end up with lithium oxide on the cathode, albeit at a lower rate because there’s simply less there. Basically, an abused battery quickly develops corrosion on both poles of the battery, inside the case.
The more you abuse the battery, the worse the corrosion gets. With corrosion taking place, the resistance goes up and the battery then has to work even harder which causes more damage, so it’s a vicious circle! Regardless of quality, over-discharging lithium polymer batteries is the most common cause of puffing, so hopefully this emphasises the problem and reminds you just how damaging it is to flatten your batteries!
As already stated, heat is a big factor. If a battery is pushed beyond 60ºC during discharge or charging, problems occur due to metallic lithium generation, which damages the cell and again, causes puffing.
The maximum voltage for a cell is 4.235V per cell, but this only possible when cell temperature is at around 60ºC. The maximum voltage at room temperature is around 4.2V per cell. Below 10ºC that figure can drop to just 4.0V. Going beyond these figures, the over-abundance of electrons will again break chemical bonds and free lithium to bond with oxygen creating lithium oxide and again, more puffing!
Once a battery has cooled down, the puffiness can reduce and most will generally keep using the battery, so if that’s you then keep on eye on it. Ideally, you should stop using a battery once it remains in a puffed state as you run the risk of fire, should the cell rupture, so be warned!
Need a set of tools to work on a drone, working with all of those tiny screws can be a pain in the butt, check out the LB1 high performance tool kit.
When to Retire Lithium Polymer Batteries?
There are so many variables that determine the lifespan of your batteries and if a pack is abused, it will only last a handful of charges, yet if treated properly, you’ll see 200+ cycles from your packs. This of course depends on your application. As a general rule, when your battery no longer holds more than 80% of its original capacity, it’s time to retire your pack and certainly if there is excessive puffing.
Unlike NiCd or NiMH batteries, Lithium Polymer batteries are environmentally friendly. For safety reasons, it’s best that lithium polymer batteries be fully discharged before their disposal and this should of course take place outdoors in the open for obvious reasons. A slow discharge to completely flat with a bulb or series of bulbs is now what I do. Once all cells are showing zero voltage, it is pretty safe to assume the pack is now inert.
Unlike other batteries, inert LiPos can be simply thrown in your normal trash. If a battery is physically damaged then, discharging fully could be dangerous and greater care is required when disposing! Search the Internet and you’ll soon find various recommended solutions for disposal. YouTube is a great source of how NOT to do it and if you’ve not seen a fire, then please have a look, it’ll certainly make you think!
That’s about it for this installment. Hopefully this feature will help you appreciate and get the very best from your batteries. Drone battery care is an ever-evolving subject. I’m always open to feedback and would love to hear from other people and their real world experiences. For me it’s all about spreading the word with accuracy and integrity. Without our batteries we couldn’t do what we do!